Manual.ly Logo

Dremel Stylo+ 2050 Rokasgramata

4,0 · 4 Vērtējumi

PDF rokasgrāmata · 164 lapas

Latviešu

M: GO-GEM-FL-25
lapa

/ 164

Loading...
9c8eef9c2a66ff041a179419530e90183af9 page 9
SAFETY INSTRUCTIONS FOR
ALL OPERATIONS
SAFETY WARNINGS COMMON FOR GRINDING,
SANDING, WIRE BRUSHING, POLISHING, CARVING OR
ABRASIVE CUTTING-OFF OPERATIONS
a. This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off tool.
Read all safety warnings, instructions, illustrations

Failure to follow all instructions listed below may result
in electric shock, re and/or serious injury.
b. 
designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
c. The rated speed of the grinding accessories must
be at least equal to the maximum speed marked on
the power tool. Grinding accessories running faster
than their rated speed can break and y apart.
d. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories cannot
be adequately controlled.
e. The arbour size of wheels, sanding drums or any

collet of the power tool. Accessories that do not
match the mounting hardware of the power tool will run
out of balance, vibrate excessively and may cause loss
of control.
f. Mandrel mounted wheels, sanding drums, cutters
or other accessories must be fully inserted into
the collet or chuck. If the mandrel is insufciently
held and/or the overhang of the wheel is too long, the
mounted wheel may become loose and be ejected at
high velocity.
g. Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, sanding drum for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute. Damaged
accessories will normally break apart during this test time.
h. Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments. The eye protection must be capable of
stopping ying debris generated by various operations.
The dust mask or respirator must be capable of
ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may cause
hearing loss.
i. Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken accessory may y away and
cause injury beyond immediate area of operation.
j. Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
k. 
the start-up. The reaction torque of the motor, as it
accelerates to full speed, can cause the tool to twist.
l. Use clamps to support workpiece whenever
practical. Never hold a small workpiece in one
hand and the tool in the other hand while in use.
Clamping a small workpiece allows you to use your
hand(s) to control the tool. Round material such as
dowel rods, pipes or tubing have a tendency to roll
while being cut, and may cause the bit to bind or jump
toward you.
m. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
n. Never lay the power tool down until the accessory
has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
o. After changing the bits or making any adjustments,
make sure the collet nut, chuck or any other
adjustment devices are securely tightened. Loose
adjustment devices can unexpectedly shift, causing
loss of control, loose rotating components will be
violently thrown.
p. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
q. Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
r. 
materials. Sparks could ignite these materials.
s. Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, sanding band, brush or any other
accessory. Pinching or snagging causes rapid stalling
of the rotating accessory which in turn causes the
uncontrolled power tool to be forced in the direction
opposite of the accessory’s rotation.
For example, if an abrasive wheel is snagged or pinched
by the workpiece, the edge of the wheel that is entering
into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may
either jump toward or away from the operator, depending on
direction of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a. 
your body and arm to allow you to resist kickback
forces. The operator can control kickback forces, if
proper precautions are taken.
b. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory and cause
loss of control or kickback.
c. Do not attach a toothed saw blade. Such blades
create frequent kickback and loss of control.
d. Always feed the bit into the material in the same
direction as the cutting edge is exiting from the
material (which is the same direction as the chips
are thrown). Feeding the tool in the wrong direction
causes the cutting edge of the bit to climb out of the
work and pull the tool in the direction of this feed.
9

Sarunājieties ar savu Dremel Stylo+ 2050 rokasgrāmatu, izmantojot AI

Saņemiet tūlītējas AI atbildes no savas Dremel Stylo+ 2050 rokasgrāmatas

Jautājiet ko vien vēlaties par Dremel Stylo+ 2050. Atbildes nāk no šīs rokasgrāmatas, norādot lapas, uz kurām tās balstītas.

Stylo+ 2050 Apkopes grafiks

Regulāri
Notīriet ventilācijas atveres un slēdzu sviras

Uzturiet gaisa caurules un slēdzu sviras tīras un brīvās no svešiem priekšmetiem, izmantojot sausu saspiešto gaisu. Nelieciet asus priekšmetus.

Pirms katras lietošanas reizes
Pārbaudiet piederumus bojājumiem

Pirms katras darbības pārbaudiet dzirnavu riteni uz skaldījumiem un plaisām, smilšpapīra tamburus uz plīsumiem vai nodilumu un stieples sukas uz vaļīgām stieplēm.

M: QW-35-FL

Uzdot Jautājumu

0/1000

Vai jūs ieteiktu Stylo+ 2050?

Jā Nē
0
User Pic

Benoît Hamel

pirms 8 mēnešiem

Man šķiet, ka patronas bloķēšanas poga ir neveikla. Kad es izslēdzu ierīci, es nejauši nospiežu to kopā ar ieslēgšanas pogu, un tā rada čīkstošu skaņu. Vai tas ir normāli un kā es to varu novērst?

0
User Pic

Manual.ly

pirms 8 mēnešiem

Uzbāžņa bloķēšanas slēdzis atrodas pretī ieslēgšanas pogai, tāpēc, nospiežot abus vienlaicīgi, var rasties īss mehānisks troksnis. Lai to novērstu, pārliecinieties, ka, izslēdzot ierīci, uzbāžņa bloķēšana nav ieslēgta: vispirms izslēdziet strāvu, pēc tam ar otru roku atbrīvojiet bloķētāju (vai uz brīdi apstājieties, lai pirksti nebūtu uz abām pogām). Pēc tam atsāciet normālu darbību. Ja troksnis turpinās pat tad, ja uzmanīgi nespiedat abas pogas vienlaicīgi, mēģiniet notīrīt ap slēdža zonu un pārbaudiet, vai nav redzamu šķēršļu. Ja tas joprojām saglabājas, lūdzu, sazinieties ar atbalsta dienestu ar īsu video, lai mēs varētu pārskatīt ierīci.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Biežāk uzdotie Jautājumi

A

Tas vislabāk der detalizētiem darbiem, piemēram, gravēšanai, pulēšanai, slīpēšanai, grebšanai, tīrīšanai un vieglai griešanai. Tā slaidā forma ir īpaši noderīga tad, kad precizitāte ir svarīgāka par jaudu.

Vai šī atbilde bija noderīga?

A

Jā, šī versija ietver piederumus, padarot to gatavu dažādiem nelieliem projektiem. Komplektā iekļautie rīki paplašina tā lietojumu tālāk par vienkāršu slīpmašīnu un atbalsta radošākus pielietojumus.

Vai šī atbilde bija noderīga?

A

Jā. Instrumentam ir maināms ātruma regulējums, tāpēc veiktspēju var pielāgot materiālam un uzdevumam. Zemāki ātrumi ir noderīgi pulēšanai; lielāki ātrumi ir piemēroti cietākiem materiāliem.

Vai šī atbilde bija noderīga?

A

Jā. Tā konusveida, pildspalvai līdzīgais dizains ir radīts kontrolei un komfortam. Tas rokā jūtas dabiski un ir ideāls smalkām, vadītām kustībām pa nelielām virsmām.

Vai šī atbilde bija noderīga?

A

Lietojiet atbilstošu acu un putekļu aizsardzību, izvairieties no pārmērīga spiediena un pārliecinieties, ka piederumi ir droši nostiprināti. Tāpat izvēlieties materiālam pareizo ātrumu, lai izvairītos no bojājumiem.

Vai šī atbilde bija noderīga?

A

Tas ir vairāk piemērots precizitātes un viegliem darbiem nekā smagai slīpēšanai. Ja nepieciešama intensīva materiāla noņemšana, labāka izvēle būs lielāks un jaudīgāks instruments.

Vai šī atbilde bija noderīga?

M: GO-GEM-FL-25

Priekšrocības un Mīnusi

Priekšrocības

  • Slaids pildspalvas stila rokturis padara detalizētu darbu vieglāku un ērtāku.
  • Maināms ātrums palīdz pielāgoties dažādiem materiāliem un uzdevumiem.
  • Saderība ar vairākiem piederumiem pulēšanai, grebšanai, slīpēšanai un gravēšanai.
  • Viegls korpuss samazina nogurumu ilgākos projektos.
VS

Trūkumi

  • Nav ideāli piemērots smagam slīpēšanas darbam vai agresīvai materiāla noņemšanai.
  • Labākie rezultāti prasa rūpīgu ātruma izvēli un vieglu pieskārienu.
  • Dažu piederumu uzstādīšanai un balansēšanai var būt nepieciešama prakse.
  • Lietošanas laikā joprojām ir svarīgi putekļi, troksnis un drošības pasākumi.
M: GO-GEM-FL-25

Produkts Specifikācija

Tips

Taisnā slīpmašīna

Jauda

9W (230V)

Apgriezienu skaits bez slodzes

5000-22000/min

Instrumentu turētājs

0,8-3,2 mm ātri atbrīvojamā urbjpatrona, ietvere

Ātruma funkcijas

Ātruma regulēšana

Svars

110 g

Piegādes komplektācija

15 gab. piederumu komplekts

M: GO-GEM-FL-25

Produkts Apraksts

Dremel Stylo+ elektriskā taisnslīpmašīna ar piederumiem (2050-15)

Dremel Stylo+ elektriskā taisnslīpmašīna ir paredzēta cilvēkiem, kuri vēlas precizitāti slaidā, ērti satveramā formātā. Tās pildspalvai līdzīgais korpuss padara to dabisku rokā, kas ir īpaši noderīgi detaļu darbiem, kur svarīgāka ir kontrole, nevis spēks. Ar komplektā iekļautajiem piederumiem šis kompaktais instruments kļūst par elastīgu palīgu pulēšanai, tīrīšanai, grebšanai, slīpēšanai, gravēšanai un viegliem griešanas darbiem.

Mazs instruments ar lielu daudzpusību

Viena no pievilcīgākajām Stylo+ īpašībām ir tā, cik pieejams tas šķiet. Masīva korpusa vietā tas piedāvā konusveida formu, kas atbalsta smalkas, vadītas kustības. Tas padara to par gudru izvēli hobiju projektiem, rokdarbu apdarei, modeļu darbiem un delikātiem remonta darbiem. Maināmais ātruma regulējums piešķir vēl vienu lietderības līmeni, ļaujot pielāgot instrumentu materiālam un uzdevumam.

Radīts detalizētam darbam

Komplektā iekļautā rokasgrāmata uzsver pareizu ātruma izvēli un drošu lietošanu, kas daudz pasaka par instrumenta mērķi: tas ir radīts, lai vislabāk strādātu ar vieglu pieskārienu. Slīpmašīna darbojas ar dažādiem Dremel piederumiem, un patronas sistēma palīdz ātrāk un ērtāk mainīt piederumus. Lietotājiem, kuri vēlas precīzāku fiksāciju, ir pieejama arī patronas uzmavu sistēma. Šī elastība ir patiesa priekšrocība, pārslēdzoties starp filca pulēšanas diskiem, slīpēšanas cilindriem, griezējiem vai gravēšanas uzgaļiem.

Praktiska veiktspēja ikdienas lietošanā

Savā būtībā Stylo+ ir par ērtumu un kontroli. Tas ir viegls, viegli manevrējams un piemērots ilgstošam darbam, kur svarīgs ir roku nogurums. Instrumenta ātrumu diapazons palīdz pieskaņot to apstrādājamajam materiālam: zemāki ātrumi ir labāki pulēšanai un jutīgiem materiāliem, bet lielāki ātrumi ir piemēroti kokam, metālam, stiklam un formēšanas darbiem. Tas padara to par uzticamu izvēli radītājiem, kuri strādā ar dažādām virsmām un tehnikām.

Svarīga ir drošība un kopšana

Tāpat kā jebkurš rotējošs instruments, Stylo+ vislabāk kalpo, ja to lieto uzmanīgi. Rokasgrāmatā uzsvērta aizsargbrilles, putekļu aizsardzības un pareizas piederumu uzstādīšanas nozīme. Tā arī atgādina izvairīties no pārmērīga spiediena, jo instruments ir paredzēts, lai darbu paveiktu piederums. Regulāra tīrīšana un pareiza uzglabāšana palīdzēs tam ilgstoši darboties vienmērīgi.

Piezīmes

  • Labākie rezultāti tiek iegūti, izvēloties pareizo piederumu un ātrumu.
  • Saudzīgs pieskāriens uzlabo precizitāti un samazina nodilumu.
  • Lietojiet atbilstošu aizsardzību, ja var rasties putekļi vai dzirksteles.

Īsāk sakot, Dremel Stylo+ ir pārdomāts risinājums precizitāti prasošiem projektiem. Tas apvieno pārnesamību, kontroli un piederumu elastību formātā, kas ļoti labi piemērots detalizētam radošajam darbam.

M: GO-GEM-FL-25

© Copyright 2026 Manual.ly